As older home electrical specialists, we are often asked the following questions:
How much does it cost to upgrade my electrical panel? What will it cost to rewire my home?
The price to upgrade an electrical panel is a question that cannot be answered precisely without an onsite visit by a qualified licensed electrician or electrical contractor.
There are many variables that affect the cost of upgrading your homes electrical system. Some of the factors are:
It is important to understand that upgrading your electrical service does not solve many of the common problems that owners of older homes experience. For example, if you often trip circuit breakers then upgrading your service will not solve that problem. Circuit breakers are doing their job when they trip because the circuit is being overloaded. The only way to resolve the problem of tripping circuits is to reduce the load on that specific circuit. That is done by adding new circuits and redistributing the load.
In San Diego, the cost of upgrading an electrical panel varies widely. We have seen prices range from $1800 all the way to over $7000. Most reputable and experienced licensed electrical contractors will be in the $2700- $6000 price range depending on the exact circumstances of your home and your electrical requirements.
Many low budget operators take shortcuts such as installing a new panel next to or on top of (not legal) your existing panel.
Some common shortcuts we see are:
Most homeowners would not know the difference if someone did a subpar electrical panel upgrade. In many cases the homeowners have to have the work completely redone at a later date.
That is why we always recommend that you check out any contractor you consider hiring thoroughly. Upgrading your electrical system is a major expense and improvement to your home and you want to be sure that it is done properly. Here is a link to a discussion on this topic.
How do I know if my electrical system needs to be upgraded? What are the signs and symptoms?
There are a number of reasons why you may need to consider replacing or upgrading your electrical panel.
Sometimes we can do a panel restoration where the internal parts of the panel are cleaned and all the breakers are replaced with new ones. For more information on older home electrical systems please visit: Inspectapedia - Zinsco
What is involved in upgrading my electrical panel? How long will it take? How much does it cost?
Upgrading your electrical panel is an involved time consuming process. However, an experienced contractor should be able to complete most if not all of the process in a single day. That is just for the panel replacement.
Here are the steps:
Once those steps are complete the power can be reconnected by the electrical contractor or SDGE. Many electricians do not patch holes so you will need to hire a stucco company to patch the hole.
Point Loma Electric is one of the few contractors who patches all of our own work and we even replace the stucco around the box. The process of removing the old panel and replacing it with a new one usually takes 1 or 2 electricians an entire day.
If all goes smoothly you will have your power restored by mid to late afternoon the same day. Patching and additional electrical work if required take longer.
Do I need a new electrical panel?
Only a licensed electrician or electrical contractor can answer this for you. Electrical panels have useful a lifespan of about 25 years. We see panels that are 50 years old and older on a regular basis. If your panel is 20 years old or older, you should have a panel safety inspection.
I just upgraded my electrical panel, why are my breakers still tripping?
The short answer is that your breakers are tripping because they are doing their job! Upgrading your panel will not resolve the issue of breakers tripping. Only adding additional circuits or taking the load off of the existing circuits.
How can I get more amps or more power to my house?
By upgrading your electrical system.
Should I replace my electrical outlets and switches?
This is a common recommendation for older homes for a number of reasons.
The electrical codes have changed and now many areas of your home require GFI protected circuits (GFCIs) These are the outlets with a reset button on them. They are required in bathrooms, kitchens, laundry areas, outdoors and anywhere water is present.
Older outlets are not grounded and often only accept 2 prong plugs but even older 3 prong receptacles many need to be replaced. If your plugs fall out easily or are loose or if you experience power outages or the receptacle is warm to the touch you should have a licensed electrician take a look.
The electrical receptacles in most home are wires using a method called “speed wiring”. During construction the receptacles are wired to each other in series by plugging the wire into a hole in the back of each device. Over time the wires often come loose causing an outage of all the other outlets downstream of the loose wire. It is only a matter of time until frequent outages become an annoyance and it is time to permanently resolve the problem by replacing the old outlets and renovating the wires so that a failure in out outlet does not affect any others.
What about Aluminum wiring?
If you have aluminum wiring in your home there are several different ways to protect your home and your family from the risk of fire. The US Consumer Safety Product Commission has published a number of electrical safety pamphlets which are available for Download Here. One booklet is specific to some of the various remedys for Aluminum wiring in your home.
What if my house has Knob and Tube wiring?
Knob and Tube wiring is one of the earliest types of residential electrical wiring. Surprisingly some older homes still have it in use. This was a very reliable and robust wiring method and if the wires have never been disturbed or tampered with in any way, it probably is still in reasonable working order. Unfortunately it is unlikely that a home that still has knob and tube wiring is fully intact and has never been tampered with or modified. Also, most insurance companies will not insure homes that contain knob and tube wiring that is still in use. It is common to replace knob and tube wiring with electrical wiring that meets todays codes and standards. Inspectapedia - Old House Wiring
In most cases use of the old knob and tube wiring should be discontinued. In some cases the knob and tube wiring is removed and other times it may be made safe and left in place. The cost of replacing old knob and tube wiring is dependant on many factors such as how difficult or easy it is to access the space between the walls. If there is clear access via either the attic or a crawl space that will make the electricians job much easier. If you have old knob and tube wiring in your home you should consider calling a licensed electrician to evaluate the condition of your homes wiring.
If your home is still has fuse boxes in place that are in use, evaluation by a qualified, licensed electrician is important. Many of the old fuse boxes are long obsolete and may be a considerable fire hazard.